Glossary · 98 terms
Say it like the trade does.
The words printed on paint cans, wallpaper labels and lumber racks, explained in plain English with a number or example you can use. Link straight to any term to share it.
98 terms
#
- 60-30-10 ruleColor
- A simple guide for balancing a room: about 60 percent dominant color (walls), 30 percent secondary (furniture or textiles), 10 percent accent. An accent wall usually counts toward the 30 or 10 portion. It is a starting point, not a law; a small room may work better at 70-20-10.
- See also: Accent color, Analogous paletteRead: How to Build a Three-Color Room Palette Around an Accent Wall
A
- Accent colorColor
- A color used in smaller doses to draw attention, contrasted against the main colors in a room. An accent wall applies it to one surface. Choose a color that relates to something else in the room, a rug, a cushion or wood tone, so it looks planned rather than random.
- See also: 60-30-10 rule, Complementary colorRead: Which Wall Should Be the Accent Wall? A Decision Method
- AcclimatizationWood & trim
- Letting wood or wood-based panels sit in the room where they will be installed, usually 48 to 72 hours, so they adjust to its temperature and humidity. Skipping it can open joints as boards shrink or cause buckling as they expand. Lay boards flat with spacers between them so air can circulate.
- See also: Veneer, MDF, Slat wallRead: How to Attach Wall Panels and Trim: Studs, Adhesive and Nails
- Analogous paletteColor
- A palette built from neighboring hues on the color wheel, such as yellow, ochre and terracotta, or green, sage and teal. It feels harmonious and calm. Add one neutral and one darker shade for depth. Most of the earthy schemes on this site are analogous with a neutral base.
- See also: Hue, Complementary colorRead: How to Build a Three-Color Room Palette Around an Accent Wall
- Angled sash brushTools
- A paintbrush with bristles cut at an angle, usually 1.5 to 2.5 inches wide, for cutting in along ceilings, corners and trim. The angle lets you place the tip exactly where you want it. A short handle is easier for curves such as arches and scallops.
- See also: Cutting in, Roller napRead: How to Cut In Paint for Crisp Accent Wall Edges
B
- Batch numberWallpaper
- A code on each wallpaper roll, sometimes called the lot or run number, identifying the print run. Ink color can shift slightly between runs, and the difference often shows only once two strips sit side by side on the wall. Buy every roll you need, plus a spare, with the same batch number, and photograph one label before throwing it out.
- See also: Drop, Waste allowanceRead: Wallpaper Batch Numbers, Spare Rolls and How Much Backup to Keep
- BattenWood & trim
- A narrow strip of wood, MDF or PVC, often 2.5 to 3.5 inches wide and 1/2 to 3/4 inch thick, fixed vertically in board and batten walls. The word also describes the thin furring strips fixed behind panels to give a flat base. Order battens in lengths that cover your full height without a joint.
- See also: Board and batten, Furring strip, MDFRead: MDF vs Pine vs PVC for Board and Batten: Which Should You Buy?
- Block brushTools
- A wide, flat brush, often 4 to 6 inches, used for limewash and mineral paints. It holds lots of thin liquid and makes the loose crisscross strokes that give limewash its movement. Natural or blended bristles work best; a roller cannot recreate the texture.
- See also: Limewash, Angled sash brushRead: How to Limewash a Wall: Prep, Coats, Brushwork and Curing
- Board and battenWood & trim
- A wall treatment of evenly spaced vertical strips (battens) between horizontal rails, all painted the same color as the wall behind. Typical spacing is 12 to 24 inches with battens 2.5 to 3.5 inches wide, at a third, half or two-thirds of the wall height. On an 11-foot wall at 14-inch spacing you need ten verticals.
- See also: Batten, Rail, Wainscoting, On centerRead: Board and Batten Spacing: How Far Apart Should Battens Be?
- BookingWallpaper
- Folding a pasted wallpaper strip pasted side to pasted side, without creasing the folds, and letting it rest for the time on the label, often 3 to 10 minutes. Booking lets paper absorb moisture and expand before it goes on the wall, so it does not bubble or open at the seams as it dries. Paste-the-wall non-wovens skip this step.
- See also: Prepasted wallpaper, Paste-the-wallRead: Paste-the-Wall vs Prepasted Wallpaper: Which Is Easier to Hang?
- Brad nailerTools
- A nail gun that fires 18-gauge brads, stronger than pins but with a small head. It is the standard choice for battens, rails and chair rail. Use brads long enough to go through the trim and into a stud by at least 3/4 inch. Fill the holes before painting.
- See also: Pin nailer, BattenRead: How to Attach Wall Panels and Trim: Studs, Adhesive and Nails
- Butt seamWallpaper
- A seam where two wallpaper strips meet edge to edge with no overlap. Most modern papers are butt-seamed: slide the new strip until it just touches the previous one, then press the seam gently with a seam roller. Pressing hard squeezes paste out and can leave a shiny line. Overlapping seams on most papers leave a visible ridge.
- See also: Double cut, Relief cutRead: How to Hang the First Strip of Wallpaper Plumb (and Where to Start)
C
- Caulk gunTools
- A tool that pushes caulk from a tube into joints. Choose a smooth-rod, dripless gun that stops the flow when you release the trigger. Cut the tube nozzle small, at a 45-degree angle, and run a thin bead. Smooth it with a damp finger. Paintable acrylic caulk is used for trim and moulding.
- See also: Board and batten, Picture-frame mouldingRead: How to Caulk, Fill and Paint MDF Trim for a Seamless Finish
- Ceiling heightMeasuring
- The distance from finished floor to ceiling, commonly 8, 9 or 10 feet in U.S. homes. Measure at several points, as it can vary by an inch or more. It decides wallpaper drop length, whether panels need a horizontal joint and whether an 8-foot board reaches without a splice.
- See also: Drop, Gross areaRead: How to Measure an Accent Wall With Windows and Doors
- Chair railWood & trim
- A horizontal moulding fixed around 32 to 36 inches above the floor, originally to protect walls from chair backs. In picture-frame moulding schemes it divides boxes above and below. A common proportion is one-third of the wall height, so about 32 inches on an 8-foot wall. It projects slightly further than the box moulding.
- See also: Picture-frame moulding, Rail, WainscotingRead: Picture Frame Moulding: How to Size and Space the Boxes
- Chalk lineTools
- A string coated in chalk that you pull tight between two points and snap to leave a straight line. It is quick for long horizontal lines and for plumb lines when hung with a weight. Use blue chalk on walls you will paint; red chalk is permanent and bleeds through.
- See also: Laser level, Plumb, LevelRead: Tools You Need for an Accent Wall, Finish by Finish
- Clear basePaint
- The base paint used for deep colors, also called deep or accent base. It contains little or no white pigment so it can hold more colorant. That makes deep colors translucent and poor at hiding, which is why they often need a tinted primer and an extra coat. The base name, often labelled base 3 or base 4 for the deepest tints, is printed on the can.
- See also: Tinted primer, Coverage rateRead: How Many Coats of Paint for Dark and Bold Colors?
- Color drenchingPaint
- Painting walls, trim, doors and sometimes the ceiling in one color, or close tones of it. It makes a room feel enveloping and hides awkward architecture. On an accent wall, the drenched version means painting that wall's trim, outlets and radiator in the same color. Use different sheens, matte on walls and satin on trim, for subtle definition.
- See also: Sheen, Satin finish, Accent colorRead: Color Drenching: Painting Walls, Trim and Ceiling One Color
- Color temperatureColor
- The warmth or coolness of a light source, measured in kelvins (K). Bulbs around 2700K are warm and yellowish, 4000K neutral, 5000K and above cool and bluish. The same paint looks different under each. Test samples under the bulbs you actually use, especially for dark or warm colors.
- See also: North-facing light, Metamerism, Warm colorRead: How to Test Paint Colors Through the Day (and Actually Decide)
- Complementary colorColor
- A color opposite another on the color wheel, such as blue and orange or green and red. Pairing complements creates lively contrast. A deep blue accent wall with brass or tan accents uses this idea in a muted way. Use one at full strength and the other in small doses.
- See also: Hue, Analogous palette, Accent colorRead: How to Build a Three-Color Room Palette Around an Accent Wall
- Cool colorColor
- A color leaning toward blue, green or violet. Cool colors tend to recede and feel calm. In bright south light they read fresh; in cool north light they can look gray and chilly. A cool accent wall can make a long room feel a little wider if it is on a short end wall, such as a 10-foot wall at the end of a 20-foot room.
- See also: Warm color, UndertoneRead: Best Accent Wall Colors for North- and South-Facing Rooms
- Coped jointWood & trim
- An inside-corner joint where one moulding runs square into the corner and the other is cut to the profile of the first, so it fits over it like a puzzle piece. Coped corners stay tight as walls move with the seasons, while mitred inside corners tend to open. Used for chair rails and baseboards rather than small boxes.
- See also: Mitre joint, Chair railRead: Mitre vs Cope: How to Join Moulding Corners Without Gaps
- Coverage ratePaint
- The area one container of paint or limewash covers in a single coat, printed on the label, typically 250 to 400 square feet per gallon for paint. Rough, porous or patched walls use more. A 12 by 8-foot wall is 96 square feet; two coats need 192, so one gallon at 350 square feet covers it with room to spare.
- See also: Net area, Waste allowance, Recoat timeRead: How Much Paint Do You Need for an Accent Wall?
- Cure timePaint
- The time paint takes to harden fully, which is far longer than drying. Paint can be dry to the touch in an hour but take several days to a few weeks to reach full hardness. Before it cures, avoid scrubbing, pushing furniture against it or applying tape or peel-and-stick paper. Many water-based wall paints quote 14 to 30 days; check the label for the maker's figure.
- See also: Recoat time, Peel-and-stick wallpaperRead: Weekend Accent Wall Timeline: An Hour-by-Hour Plan
- Cutting inPaint
- Painting a neat band, usually 2 to 3 inches wide, with a brush along ceilings, corners and trim before rolling the rest of the wall. On an accent wall, cutting in is where the crisp line between colors comes from. Roll within the hour so the cut-in band blends; otherwise it dries into a visible frame.
- See also: Wet edge, Angled sash brush, Painter's tapeRead: How to Cut In Paint for Crisp Accent Wall Edges
D
- Double cutWallpaper
- A technique for a perfect seam where two strips overlap by an inch or two and you cut through both layers at once with a straight edge and a sharp blade. Peel away the two offcuts and the edges meet exactly. It is used on grasscloth, murals and inside corners, but press lightly so you do not score the drywall.
- See also: Butt seam, Snap-off knifeRead: How to Hang the First Strip of Wallpaper Plumb (and Where to Start)
- DropWallpaper
- One full-height length of wallpaper cut from a roll, also called a strip. Drop length is the wall height plus trim allowance, rounded up to the pattern repeat for matched papers. On a 9-foot ceiling with a 21-inch repeat and 4 inches of trim, each drop is 126 inches, so a standard 33-foot roll yields three drops, not four.
- See also: Pattern repeat, Batch number, Free matchRead: How Many Wallpaper Rolls? Count Full Strips, Not Square Feet
E
- EggshellPaint
- A finish with a soft, low sheen, a step above matte. It wipes clean more easily and suits living rooms, hallways and bedrooms with some wear. On a flawed wall it shows a little more texture than matte. On a two-sheen moulding scheme, eggshell walls with satin trim make boxes stand out by reflection alone.
- See also: Sheen, Matte finish, Satin finishRead: Paint Sheen Guide: Flat, Matte, Eggshell, Satin or Gloss?
F
- FlashingPaint
- Uneven sheen across a painted wall, where some patches look shinier or duller than the rest. It often appears over filled patches that were not primed, because filler absorbs paint differently. Spot-prime every patch, use enough paint per coat, and avoid touching up small areas on a finished wall, which nearly always flashes. A 2-inch filled nail hole left unprimed can show as a dull spot in side light.
- See also: Lap marks, Tinted primer, SheenRead: Paint Touch-Ups That Don't Show and How to Store Leftovers
- Fluted panelWood & trim
- A panel with rounded vertical ribs, or flutes, machined into the face, sold in MDF, veneer or polymer, often 2 feet wide and 8 to 9 feet tall. Flutes add height and catch side light. Plan the layout from the center of the main feature so cut panels at each end are equal.
- See also: Veneer, MDF, Slat wallRead: Fluted Wall Panels: How to Plan the Layout and Order
- Free matchWallpaper
- A wallpaper with no horizontal alignment between strips, such as plain stripes, textured grasscloth or an all-over random design. You can cut every drop to wall height plus trim and hang it in any order. On an 8-foot wall with 4 inches of trim, each drop is 100 inches, so a 33-foot roll gives three full drops with a little over a foot left.
- See also: Straight match, Pattern repeat, GrassclothRead: Wallpaper Label Symbols, Roll Sizes and Match Types Explained
- Furring stripWood & trim
- A thin strip of wood, often a 1x2 or 1x3, fixed to studs to create a flat, level base for panels or slats. It also creates a cavity behind the finish for cables or acoustic felt. Shim behind low spots with thin packers until the strips line up against a long straight edge.
- See also: Batten, Stud spacing, Slat wallRead: How to Attach Wall Panels and Trim: Studs, Adhesive and Nails
G
- GrassclothWallpaper
- A natural wallcovering woven from grasses, jute, sisal or hemp and glued to a paper backing. Each strip varies in color and texture, so visible seams are part of the look, not a fault. It stains easily from water and paste, is hard to clean, and shades can differ between rolls, so reverse-hang alternate strips if the maker suggests it, and order 1 extra roll.
- See also: Free match, Batch number, Butt seamRead: Grasscloth Wallpaper: How to Plan, Order and Hang It Well
- GreigeColor
- A blend of gray and beige, popular as a flexible neutral. Its undertone can lean green, pink or violet, which shows next to floors and fabrics. A greige with a warm undertone sits well with oak; a cooler one suits concrete and black metal. Always test next to your flooring.
- See also: Undertone, Warm colorRead: Paint Undertones Explained: Pick an Accent Wall Color That Behaves
- Gross areaMeasuring
- The full area of a wall before subtracting doors or windows: width times height. A 12 by 8-foot wall has a gross area of 96 square feet. Wallpaper and panels are usually estimated from gross area, because cutouts around openings rarely produce usable pieces. Paint and limewash use net area.
- See also: Net area, Square feet to square metersRead: How to Measure an Accent Wall With Windows and Doors
H
- Half-drop matchWallpaper
- A pattern where the motif on every second strip sits half a repeat lower, creating a diagonal rhythm. Hang strip one, then shift strip two down by half the repeat to match. It uses more paper: with a 24-inch repeat, every alternate drop needs an extra 12 inches. Cut odd and even strips from alternate rolls to keep waste down.
- See also: Straight match, Pattern repeat, DropRead: Half-Drop vs Straight Match Wallpaper: What Changes in Your Order
- HueColor
- The basic color family, such as red, yellow, green or blue, described by its position on the color wheel. Two paints can share a hue but differ in value and saturation; a navy and a sky blue are both blue. Choosing palette colors from related hues tends to feel calm.
- See also: Saturation, Value, Analogous paletteRead: How to Build a Three-Color Room Palette Around an Accent Wall
L
- Lap marksPaint
- Darker or shinier stripes where wet paint was rolled over paint that had already started to dry. They show most on dark colors, higher sheens and in raking light from a window. Prevent them with a wet edge and full-height bands. Fix them with another full coat, edge to edge, rather than spot touch-ups. On a 12-foot wall, that is about four bands.
- See also: Wet edge, Flashing, Matte finishRead: How Many Coats of Paint for Dark and Bold Colors?
- Laser levelTools
- A tool that projects a straight horizontal or vertical line onto the wall. It is fast for marking chair rails, two-tone lines, plumb lines for wallpaper and slat layouts. A cross-line laser does both directions. Check its accuracy by marking a line, rotating the tool 180 degrees and comparing.
- See also: Plumb, Level, Chalk lineRead: Tools You Need for an Accent Wall, Finish by Finish
- LevelMeasuring
- Perfectly horizontal. Chair rails, top rails and two-tone paint lines should follow a level line rather than the floor or ceiling, which may slope. Over 13 feet, floors can drift by 1/2 inch or more. Mark the line from the highest point of the floor so nothing ends up too low.
- See also: Plumb, Laser level, Chalk lineRead: Two-Tone Walls: How High Should the Paint Line Be?
- LimewashPaint
- A traditional mineral finish made from slaked lime, water and pigment. It is brushed on in loose strokes and dries with soft, cloudy variation. It is breathable and matte, and suits plaster and masonry. Over modern painted walls it needs a mineral primer. Limewash dries much lighter than it looks wet, so judge color only once dry, at least 4 hours later.
- See also: Mineral primer, Coverage rate, Block brushRead: Limewash vs Paint: Which Finish Suits Your Accent Wall?
- Linear feetMeasuring
- A length measurement in feet regardless of width, used for trim, moulding, slats and battens. A box of picture-frame moulding 46 by 28 inches needs about 12.3 linear feet. Total your linear footage, then divide by the stick length and add waste to get the number of lengths to buy.
- See also: Waste allowance, On centerRead: Accent Wall Shopping List: Everything to Buy, by Finish
- LRVColor
- Light reflectance value, a 0 to 100 scale showing how much light a color reflects: 0 is black, 100 is perfect white. Many swatch cards list it. Colors under about 15 feel deep and enveloping; above about 60 they feel light. Mid-tone colors around 35 to 50 often work well as camera backdrops.
- See also: Value, North-facing lightRead: Light Reflectance Value (LRV) Explained for Paint and Accent Walls
M
- Matte finishPaint
- A low-sheen paint finish that reflects very little light, which hides small dents, patches and roller marks. It makes dark colors look velvety. Older mattes marked easily, but many current mattes are labelled washable or scrubbable. It is the usual first choice for deep accent colors and for walls with dents under about 1/16 inch that are not worth skimming.
- See also: Sheen, Eggshell, Lap marksRead: Best Paint Finish to Hide Wall Imperfections
- MDFWood & trim
- Medium-density fiberboard, an engineered board made from wood fibers and resin. It is smooth, stable and cheap, and paints beautifully, which makes it the default for battens, moulding and fluted panels. It swells if water gets into cut edges, so seal cuts and avoid it in showers and around tubs. Primed MDF saves a coat. Common trim stock is 1/2 or 3/4 inch thick.
- See also: PVC trim, Veneer, BattenRead: MDF vs Pine vs PVC for Board and Batten: Which Should You Buy?
- MetamerismColor
- When two colors match under one light but not another. A paint sample that matches your sofa in the store can look different under your home lighting. It is why swatches should be tested on the wall in your own daylight and evening light before buying gallons.
- See also: Color temperature, UndertoneRead: How to Test Paint Colors Through the Day (and Actually Decide)
- Mineral primerPaint
- A gritty primer, often sold by limewash makers, that gives lime and mineral paints something to grip on non-porous surfaces such as latex paint. Without it, limewash can rub off or look streaky. It is rolled on in one coat and left to dry fully, typically overnight, before the first coat of limewash.
- See also: Limewash, Tinted primerRead: Can You Limewash Over Painted Walls? Primer and Prep Explained
- Miter sawTools
- A power saw that cuts precise angles, essential for picture-frame moulding and trim. Use a fine-tooth blade, 60 teeth or more, for clean cuts on MDF. Cut test pieces first. A hand miter box with a backsaw works for a few boxes but is slow for a whole wall.
- See also: Mitre joint, Coped jointRead: Mitre vs Cope: How to Join Moulding Corners Without Gaps
- Mitre jointWood & trim
- A corner joint where two pieces are each cut at 45 degrees and meet to form 90 degrees, the standard joint for picture-frame moulding boxes. Each box has four corners and eight mitre cuts. Cut a test pair from offcuts first; a tiny angle error on each piece doubles at the joint and leaves a visible gap.
- See also: Coped joint, Miter saw, Picture-frame mouldingRead: Mitre vs Cope: How to Join Moulding Corners Without Gaps
- Mural panelWallpaper
- One numbered section of a large printed image, often 18 to 36 inches wide, that together form a mural. Unlike rolls, panels are ordered to your wall's exact size plus bleed, usually a few inches on each side. Lay them out on the floor in order before pasting; a missing or misprinted panel cannot be fixed once the run is half up.
- See also: Butt seam, Drop, Free matchRead: Mural Wallpaper Sizing: How to Measure, Add Bleed and Count Panels
N
- Net areaMeasuring
- Wall area after subtracting doors, windows and other openings you will not cover. A 14 by 9-foot wall (126 sq ft) with a 3 by 7-foot doorway (21 sq ft) has a net area of 105 square feet. Use net area for paint and limewash quantities; subtract each opening only once, even if two overlap.
- See also: Gross area, Coverage rate, Waste allowanceRead: How to Measure an Accent Wall With Windows and Doors
- Non-woven wallpaperWallpaper
- Wallpaper made with a fabric-like blend of natural and synthetic fibers that does not expand when wet. Because it stays dimensionally stable, it is usually hung paste-the-wall and seams stay tight. Most non-woven papers strip off dry in whole sheets, which makes them the friendliest choice for a first accent wall. A typical roll is 20.5 inches wide and 33 feet long.
- See also: Paste-the-wall, Vinyl wallpaper, Peel-and-stick wallpaperRead: Paste-the-Wall vs Prepasted Wallpaper: Which Is Easier to Hang?
- North-facing lightColor
- In the Northern Hemisphere, rooms with windows facing north get indirect, cool, consistent light. It makes colors look grayer and cooler. Warm colors and those with yellow or red undertones balance it. South-facing rooms get warm, strong light that brightens and warms colors through the day. Test swatches at 9 a.m., 1 p.m. and after dark.
- See also: Warm color, Cool color, Color temperatureRead: Best Accent Wall Colors for North- and South-Facing Rooms
O
- On centerMeasuring
- A distance measured from the center of one member to the center of the next, written o.c. Stud spacing (16 inches o.c.) and batten spacing are both given this way. For board and batten, a 16-inch o.c. layout with 2.5-inch boards leaves about 13.5 inches of clear wall between battens.
- See also: Stud spacing, Board and battenRead: Board and Batten Spacing: How Far Apart Should Battens Be?
- Oscillating multi-toolTools
- A handheld power tool with a vibrating blade that makes precise plunge cuts. It is useful for trimming baseboards in place, cutting slats around outlets and undercutting door casings. Use a fine-tooth wood blade for trim and a carbide blade if you hit nails. Cut 1/16 inch outside the line and sand to it.
- See also: Slat wall, Miter sawRead: Slat Wall Layout Around Outlets and Switches: A Planning Guide
- Out of squareMeasuring
- When corners are not exactly 90 degrees or a wall is not the same width at the top and bottom. Measure width at the top, middle and bottom; a difference of more than 1/4 inch means panels and slats need scribing or a shadow gap at one end. Use the largest dimension when ordering.
- See also: Plumb, Scribing, Shadow gapRead: Accent Walls on Uneven Walls and Sloping Ceilings
P
- Painter's tapeTools
- Low-tack masking tape for protecting edges while painting. Delicate-surface tapes are for fresh paint less than a week old. Press the edge firmly, and seal it with a thin coat of the base color for very crisp lines. Pull at a 45-degree angle while the last coat is still wet.
- See also: Cutting in, LevelRead: Geometric Accent Wall: Tape Layouts, Paint and Planning
- Paste-the-wallWallpaper
- A hanging method where adhesive goes on the wall rather than the back of the paper, usually used with non-woven wallpapers. You roll paste onto an area slightly wider than one strip, then hang the dry strip straight from the roll. There is no soaking or booking, strips can slide into position, and most come off dry later.
- See also: Non-woven wallpaper, Prepasted wallpaper, BookingRead: Paste-the-Wall vs Prepasted Wallpaper: Which Is Easier to Hang?
- Pattern repeatWallpaper
- The vertical distance before a wallpaper design starts again, printed on the label in inches or centimeters. It decides how much paper each strip wastes: on an 8-foot wall with 4 inches of trim, a 21-inch repeat makes every drop round up to 105 inches, so nine inches go in the bin per strip. Bigger repeats mean more waste and fewer strips per roll.
- See also: Straight match, Half-drop match, Drop, Free matchRead: How Many Wallpaper Rolls? Count Full Strips, Not Square Feet
- Peel-and-stick wallpaperWallpaper
- Self-adhesive wallpaper with a backing liner you peel away as you hang. It is popular with renters because it can come off without water or scraping when the wall paint is sound. It sticks poorly to fresh paint, textured walls and flat paint, so wait about 4 weeks after painting and test a sample for 7 days before buying the lot.
- See also: Non-woven wallpaper, Relief cutRead: Is Your Wall Ready for Peel-and-Stick Wallpaper? A Readiness Check
- Picture-frame mouldingWood & trim
- Rectangles of thin applied moulding, mitred at the corners, fixed to a flat wall to suggest classical panelling. Boxes are usually set with equal margins of 3 to 5 inches from rails and corners. On a 13-foot wall, three boxes with 4-inch gaps come out about 47 inches wide. Paint wall and moulding together for a tonal look.
- See also: Chair rail, Mitre joint, Coped jointRead: Picture Frame Moulding: How to Size and Space the Boxes
- Pin nailerTools
- A nail gun that drives very thin headless pins, typically 23 gauge. The holes are almost invisible, making it ideal for moulding and slats held mainly by adhesive. Pins have little holding power alone, so use adhesive or a brad nailer for heavier pieces.
- See also: Brad nailer, Picture-frame mouldingRead: How to Attach Wall Panels and Trim: Studs, Adhesive and Nails
- Plate railWood & trim
- A narrow shelf, usually 3 to 4 inches deep, set on top of wainscoting or board and batten, with a groove or lip near the back for leaning plates and art. It suits dining rooms with tall batten at around 5 to 6 feet. Screw it into studs, not just into the trim below.
- See also: Rail, Board and battenRead: How High Should Board and Batten Go? Heights That Look Right
- PlumbMeasuring
- Perfectly vertical, as found by gravity. Walls and corners are often slightly off plumb, so wallpaper, slats and battens should be aligned to a plumb line, not to the corner. A wall that leans 1/4 inch over 8 feet is common. Check with a long spirit level or a laser.
- See also: Level, Laser level, Out of squareRead: How to Hang the First Strip of Wallpaper Plumb (and Where to Start)
- Prepasted wallpaperWallpaper
- Wallpaper with dry adhesive already on the back, activated by dipping the strip in water or wetting it with a sponge. After activation it usually needs booking for a few minutes so the paper relaxes. It is convenient, but too little water leaves dry patches that lift and too much makes seams slip. Follow the label's soak time, often 10 to 30 seconds in the tray, to the second.
- See also: Booking, Paste-the-wall, Vinyl wallpaperRead: Paste-the-Wall vs Prepasted Wallpaper: Which Is Easier to Hang?
- PVC trimWood & trim
- Trim boards made from cellular PVC, a waterproof plastic that cuts and nails like wood. It does not rot or swell, making it ideal for bathroom board and batten. It needs a bonding primer before paint, and very dark colors in hot sun can make it move. It often costs 1.5 to 2 times as much as MDF but lasts in wet rooms.
- See also: MDF, Board and battenRead: MDF vs Pine vs PVC for Board and Batten: Which Should You Buy?
R
- RailWood & trim
- A horizontal member in board and batten or wainscoting: a top rail where the treatment ends and a bottom rail, often the baseboard. The top rail is usually the same width as the battens or slightly wider, and may carry a small cap or ledge. Fix rails first and measure every vertical between them individually; floors can vary by 1/4 inch along a 12-foot wall.
- See also: Board and batten, Chair rail, Plate railRead: How High Should Board and Batten Go? Heights That Look Right
- Recoat timePaint
- How long to wait before applying the next coat, printed on the label, often 2 to 4 hours for water-based wall paint at room temperature. Recoating too early drags the soft first coat and leaves rough patches. Cold, humid rooms slow drying, so add time when it is below about 60°F or very damp.
- See also: Cure time, Coverage rateRead: Weekend Accent Wall Timeline: An Hour-by-Hour Plan
- Relief cutWallpaper
- A short diagonal cut into wallpaper at the corner of a window frame, door casing or outlet so the paper can lie flat around it. You hang the strip over the opening, cut from the paper's edge toward the frame corner, then fold back and trim along the casing. Stop the cut about 1/8 inch short of the corner first; a cut that goes too far shows.
- See also: Butt seam, DropRead: Wallpaper Around Windows, Outlets and Corners Without Gaps
- Roller napTools
- The thickness of a paint roller cover's fibers, usually 1/4 to 3/4 inch. Short naps, 1/4 to 3/8 inch, suit smooth walls and leave a fine finish. Longer naps hold more paint and reach into textured surfaces. Microfiber covers with a 3/8-inch nap are a good all-rounder for accent walls.
- See also: Angled sash brush, Wet edgeRead: Tools You Need for an Accent Wall, Finish by Finish
- Rounding upMeasuring
- Buying whole containers, rolls or boards after calculating a fractional need. If you need 2.1 gallons, you buy three, not two. Always round each item at the final step, after adding waste. Rounding each wall separately before adding them together can overstate how much you need.
- See also: Waste allowance, Coverage rateRead: Compare Usable Quantity, Not Price per Roll, Can or Panel
S
- Satin finishPaint
- A medium-sheen finish that is durable and wipeable, common on trim, doors, battens and kids' rooms. It shows lap marks and patches more than matte, so roll with a wet edge and good light. Painting board and batten in satin and the wall above in matte helps the panelling read as a separate zone, even when both are the same color, such as one 4-foot band of satin batten under matte wall.
- See also: Sheen, Eggshell, Semi-gloss, Wet edgeRead: Paint Sheen Guide: Flat, Matte, Eggshell, Satin or Gloss?
- SaturationColor
- How intense or pure a color is, from vivid to grayed. A muted or dusty color has lower saturation. Low-saturation colors are easier to live with on large walls; a highly saturated color often looks stronger once it covers a whole wall than it did on a 2-inch swatch. Test with a sample at least 12 by 12 inches.
- See also: Hue, ValueRead: How to Build a Three-Color Room Palette Around an Accent Wall
- ScribingWood & trim
- Marking and cutting a board to follow an uneven surface, such as a wavy wall or sloped floor. Hold the board in place, run a compass or a pencil on a spacer along the wall, and cut to the line. It is how you fit the first and last panel tight to an out-of-plumb corner.
- See also: Shadow gap, Out of square, PlumbRead: Accent Walls on Uneven Walls and Sloping Ceilings
- Seam rollerTools
- A small roller used to press wallpaper seams flat. Use gentle pressure; too much squeezes out paste and leaves a shiny line or flattens embossed paper. Wipe the roller clean between seams. Some papers say not to use one, so check the instructions.
- See also: Butt seam, Wallpaper smootherRead: How to Hang the First Strip of Wallpaper Plumb (and Where to Start)
- Semi-glossPaint
- A shiny, hard-wearing finish used on trim, doors, cabinets and bathroom woodwork. It shrugs off moisture and scrubbing but highlights every flaw. On an accent wall itself it is rarely a good choice; a 100-square-foot semi-gloss surface reflects windows and lights like a mirror and shows each roller pass.
- See also: Sheen, Satin finishRead: Paint Sheen Guide: Flat, Matte, Eggshell, Satin or Gloss?
- Shadow gapWood & trim
- A small, deliberate gap, typically 1/4 to 1/2 inch, left between a panel and an adjacent surface such as a ceiling or wall. It hides small irregularities because the eye reads a crisp shadow instead of a wobbly joint. Shadow gaps work well at the ends of slat and panel walls where corners are out of plumb.
- See also: Slat wall, Scribing, Out of squareRead: How to Attach Wall Panels and Trim: Studs, Adhesive and Nails
- SheenPaint
- How much light a dried paint surface reflects, from flat through matte, eggshell, satin, semi-gloss and gloss. Higher sheen is tougher and easier to clean but shows every dent, roller lap and patch. A common split for an accent wall: matte or eggshell on the wall, satin or semi-gloss on trim. Sheen names vary by maker, so compare 2 or 3 sample boards in raking light.
- See also: Matte finish, Eggshell, Satin finish, Semi-glossRead: Paint Sheen Guide: Flat, Matte, Eggshell, Satin or Gloss?
- ShiplapWood & trim
- Wall boards with rabbeted edges that overlap, leaving a narrow consistent gap between each board, often 1/8 to 1/4 inch. Usually laid horizontally, it reads as farmhouse; vertically it reads more modern. Boards are commonly 6 to 8 inches wide. Painting the wall behind it the same color first stops raw wall showing in the gaps.
- See also: Wainscoting, Board and batten, Shadow gapRead: Shiplap Accent Wall: How to Plan Rows, Boards and Joints
- Slat wallWood & trim
- A wall of narrow vertical strips fixed with even gaps, either from individual boards or felt-backed panels. Common sizes are slats 1.5 to 2 inches wide with gaps of 3/4 to 1.25 inches. A 9-foot wall with 1.5-inch slats and 3/4-inch gaps takes 49 slats. Paint the wall behind dark so the gaps read as shadow.
- See also: Shadow gap, Fluted panel, Furring stripRead: DIY Slat Wall From Lumber: Spacing, Cut List and Finish
- Snap-off knifeTools
- A utility knife with a segmented blade you snap off to expose a fresh edge. Wallpaper must be trimmed with a sharp blade, so snap often, every strip or two. A dull blade tears wet paper and leaves ragged edges at ceilings and baseboards.
- See also: Double cut, Wallpaper smootherRead: How to Hang the First Strip of Wallpaper Plumb (and Where to Start)
- Spacer blockTools
- A small block cut to the exact gap you want between slats, battens or moulding boxes. Using the same block for every gap gives consistent spacing, which matters more than the exact measurement. Cut two in case one goes missing, and mark them clearly.
- See also: Slat wall, Board and battenRead: DIY Slat Wall From Lumber: Spacing, Cut List and Finish
- Square feet to square metersMeasuring
- One square meter equals about 10.764 square feet, so divide square feet by 10.764 to convert. A 96-square-foot wall is about 8.9 square meters. Convert at the end of a calculation, not each dimension separately, to avoid rounding errors that can add up to a whole extra can or roll.
- See also: Gross area, Rounding upRead: Feet, Inches and Metric: Convert Wall Measurements Without Mistakes
- Straight matchWallpaper
- A pattern that lines up horizontally at the same height on every strip, so the motif sits in a straight row across the wall. Each strip starts at the same point in the design. It is the easiest match to hang and wastes the least after free match, because every drop is the wall height plus trim rounded up to one whole repeat.
- See also: Pattern repeat, Half-drop match, Free matchRead: Half-Drop vs Straight Match Wallpaper: What Changes in Your Order
- Stud finderTools
- An electronic tool that detects the framing behind drywall by changes in density, or magnets that find screws. Find each stud's edges and mark the center. Confirm with a small nail in a spot that will be hidden. Studs are usually 1.5 inches wide. Stud finders struggle on plaster walls, so use the magnet type there.
- See also: Stud spacing, On centerRead: Tools You Need for an Accent Wall, Finish by Finish
- Stud spacingMeasuring
- The distance between the vertical framing members behind drywall, usually 16 inches on center in U.S. homes, sometimes 24 inches. Heavy items such as TV mounts, shelves, rails and hooks should screw into studs. Mark stud lines on painter's tape at the ceiling and floor before covering the wall with panels.
- See also: On center, Stud finder, Furring stripRead: How to Attach Wall Panels and Trim: Studs, Adhesive and Nails
T
- Tinted primerPaint
- Primer tinted toward the topcoat color, usually a shade of gray for deep colors or a pale version for light ones. It improves hiding so dark or bold paints cover in two coats instead of three or four. Going from white to a deep navy without it often leaves a streaky, translucent finish after two coats.
- See also: Clear base, Flashing, Wallpaper primerRead: Do You Need Primer, or Just Another Coat of Paint?
U
- UndertoneColor
- The subtle color beneath a paint's main color, such as the green in a gray or the pink in a beige. Undertones show up when colors sit side by side. Compare a sample to pure white paper to see it. A gray with a blue undertone can look cold next to oak floors with an orange undertone.
- See also: Hue, Greige, Warm colorRead: Paint Undertones Explained: Pick an Accent Wall Color That Behaves
V
- ValueColor
- How light or dark a color is, independent of its hue. Value contrast is what makes an accent wall read: a mid-tone sage next to an off-white is noticeable, while a pale sage next to the same white barely shows. Squint at samples; the lightness difference is what you are seeing. A difference of 20 or more LRV points usually reads clearly.
- See also: LRV, Saturation, HueRead: Light Reflectance Value (LRV) Explained for Paint and Accent Walls
- VeneerWood & trim
- A thin layer of real wood, often under 1 millimeter, glued to a stable core such as MDF or plywood. It gives the look of solid oak or walnut at lower cost and with less movement. Veneer cannot be sanded hard, so treat damage lightly. Sheets vary in grain, so lay them out and arrange them before fixing.
- See also: MDF, Fluted panelRead: Veneer vs MDF vs Solid Wood Wall Panels: What You're Buying
- Vinyl wallpaperWallpaper
- Wallpaper with a vinyl surface layer, either solid vinyl or vinyl-coated paper. It resists moisture and can be wiped or scrubbed, which makes it the usual choice for kitchens, laundry rooms and family bathrooms. It does not breathe, so hang it on a sound, dry wall with a mildew-resistant paste. Keep it at least 2 feet from a stove or a shower spray zone.
- See also: Non-woven wallpaper, Wallpaper primer, Prepasted wallpaperRead: Wallpaper in Bathrooms: What Survives Steam and What Peels
- VOCPaint
- Volatile organic compounds, solvents that evaporate from paint as it dries and contribute to the smell. Many water-based wall paints are sold as low-VOC or zero-VOC, which matters in nurseries and bedrooms. Zero-VOC base paint can still gain some VOCs from colorants, so check whether the claim covers tinted colors, and ventilate for 2 to 3 days either way.
- See also: Cure timeRead: Nursery and Kids Room Accent Wall Ideas That Grow With Them
W
- WainscotingWood & trim
- Panelling on the lower part of a wall, traditionally raised or flat panels in a frame, now used loosely for any lower-wall treatment. Height is usually 32 to 48 inches, or about a third of the wall. Board and batten, beadboard and picture-frame moulding below a chair rail are all forms of wainscoting.
- See also: Board and batten, Chair rail, ShiplapRead: Wainscoting vs Board and Batten vs Shiplap: Which to Choose
- Wallpaper primerWallpaper
- A primer made for wallpaper that seals the wall, gives paste even absorption and makes later removal easier. It lets you slide strips into position before the paste grabs. On new drywall it is essential: without it, wallpaper can bond to the paper face of the drywall and tear it on removal. One coat on a clean, dry wall is usually enough.
- See also: Paste-the-wall, Vinyl wallpaper, Tinted primerRead: How to Remove Wallpaper Cleanly Without Wrecking the Wall
- Wallpaper smootherTools
- A flat plastic tool used to press wallpaper onto the wall and push air bubbles out to the edges. Work from the center outward and upward, and use gentle pressure on delicate papers. A soft brush is better for grasscloth and some textured papers that a hard smoother could scratch. A 9 to 12-inch smoother covers a strip in a few passes.
- See also: Butt seam, Snap-off knifeRead: How to Hang the First Strip of Wallpaper Plumb (and Where to Start)
- Warm colorColor
- A color leaning toward red, orange or yellow, such as terracotta, ochre or cream. Warm colors feel cozy and advance visually, so a warm accent can make a wall feel closer. They balance cool north light. Even grays and whites can be warm if they have a yellow or red undertone.
- See also: Cool color, Undertone, North-facing lightRead: Best Accent Wall Colors for North- and South-Facing Rooms
- Waste allowanceMeasuring
- Extra material added to an estimate to cover offcuts, mistakes, damaged pieces and future repairs, usually 10 to 15 percent. Bump it up for half-drop wallpaper, diagonal layouts or uneven walls. On 30 slats, a 10 percent allowance means buying 33. Keeping the spare from the same batch is part of the point.
- See also: Net area, Batch number, Rounding upRead: How Much Extra Material to Buy: Waste Factors by Finish
- Wet edgePaint
- Keeping the edge of freshly applied paint wet so each new roller pass blends into it. If you roll into paint that has started to dry, you get lap marks. Work in vertical bands about 3 feet wide from ceiling to floor, and do not stop mid-wall. Dark colors and warm, dry rooms make wet edges harder to hold.
- See also: Lap marks, Flashing, Cutting inRead: How to Cut In Paint for Crisp Accent Wall Edges