roombatch

WallpaperTricky spots

Wallpaper Around Windows, Outlets and Corners Without Gaps

Flat runs of wall are the easy part. The skill in wallpapering is what happens at a window reveal, a light switch or a corner that is anything but square. This guide covers the cuts, the order of work and the planning choice that surprises most people: why a window barely reduces the number of rolls you buy.

9 min readPublished By the RoomBatch editorial team
On this page
  1. Key takeaways
  2. Why openings do not shrink your order much
  3. Outlets and switches: power off, plate off, paper over
  4. Windows and doors: the relief-cut method
  5. Inside corners: split, replumb, overlap
  6. Outside corners: wrap, do not seam
  7. Plan the wall before the first cut
  8. Questions

Key takeaways

  • Turn off power and remove faceplates first. Paper over the box, then cut it open; never cut around a plate that is still on.
  • Hang full-height strips over a window, cut away the opening, and trim. The pattern above and below stays aligned.
  • Never wrap more than about 1/2 in around an inside corner. Split the strip, draw a new plumb line, and overlap the offcut.
  • Keep seams at least 6 in from inside and outside corners where possible, and avoid narrow slivers above doors and below windows.
  • RoomBatch does not deduct openings. A 3 ft by 4 ft window rarely saves a whole roll once the pattern has to line up.

Why openings do not shrink your order much

It feels logical to subtract the window. In paint math it works. In wallpaper math it mostly does not, because the strip above a window and the strip below it are still part of the same column. They must start at the right pattern position, and they are usually cut from the same full drop or from offcuts that happen to sit at the right point in the design.

RoomBatch keeps every strip full height and says so in its assumptions: openings are not deducted, so cut-outs become spare. Here is why that is a fair default. On a 12 ft by 8 ft wall with 20.5 in by 33 ft rolls and a 21 in straight repeat, you hang 8 strips of 105 in. Three fit on each 396 in roll, so 3 rolls give 9 drops: 8 to hang plus 1 spare. Put a 36 in wide window in the middle and it touches two or three strips. The short pieces above and below each still need their own correctly matched cuts. At best you might save one drop. That does not remove a roll, because rolls come in steps of three drops here.

Why openings do not shrink your order much
12 x 8 ft wall, 21 in repeatNo windowWith a 3 x 4 ft window
Strips crossing the wall88 (2 to 3 are partial)
Drops per 33 ft roll33
Rolls with 1 spare strip33
What the window really saves-One or two short pieces, kept as repair stock

Outlets and switches: power off, plate off, paper over

Brewster's instructions open with safety: turn off power to outlets and switches and remove all faceplates and socket covers. Wet paste, a metal blade and a live box are a bad combination. Test that the circuit is dead before you start.

Hang the strip straight over the box as if it were not there. Smooth down to just above it, then press lightly to feel the opening. Make two diagonal cuts from corner to corner of the box in an X, fold the four triangles back, and trim them along the box edge with a sharp blade. Smooth the rest of the strip, sponge paste off the box rim, and leave the faceplate off until the paste has dried.

  • Cut just inside the box edge. The faceplate covers about 1/4 in on every side.
  • Do not paper inside the electrical box itself.
  • For a thermostat, mark its mounting holes before removing it; hang the paper and refit it, or plan to leave it unpapered behind.
  • If you want an invisible switch, cut a small piece of matching offcut to wrap the faceplate. Match it while the plate is held in place, then glue it on the bench.

Windows and doors: the relief-cut method

Hang the strip that meets the window frame as a full drop, letting it lap over the opening. Smooth it down the wall beside the frame. Then make a diagonal relief cut from the waste edge toward the outer corner of the frame, at both the top and bottom corners. That lets the paper fold neatly around the frame while the rest stays flat.

Press the paper into the frame edge with a putty knife and trim with a fresh blade. Continue with full drops over the opening. For the short strips above and below the window, cut them from drops or offcuts that start at the right pattern position, and use your level: a window frame is not a plumb line.

When you reach the far side of the window, the next full strip must line up with the pattern above and below. Check it against both short strips before pasting, because small errors over the window show most at its far edge.

Windows and doors: the relief-cut method
OpeningCut typeWatch out for
Outlet or switchX cut, then trim to the box edgePower off; faceplate covers the rim
Window with frameDiagonal relief cut at each corner, then trimPattern alignment above and below
Window with deep revealWrap side reveals; patch the head revealSeams on the reveal edge lift; keep them on the face
Door frameRelief cut at the top cornerShort strip over the door needs its own pattern match
Radiator or pipeSlit from the bottom edge to the pipeHeat can lift paste; follow the maker's advice

Inside corners: split, replumb, overlap

Never try to turn a full strip around an inside corner. Walls are rarely plumb, so the paper twists, and the edge on the new wall wanders off vertical. Measure from the edge of the last strip to the corner at the top, middle and bottom. Add 1/2 in to the widest measurement and cut that width from the next drop.

Hang that piece so it wraps 1/2 in onto the next wall. Then draw a new plumb line on the next wall, the offcut's width out from the corner. Hang the offcut to that line, lapping over the 1/2 in wrap, and trim it along the corner if the paper is thick enough to show a ridge. The pattern loses a little at the corner, but the eye never sees it in an inside angle.

Wolf-Gordon's guidance for grasscloth and other natural coverings is strict here: keep vertical joints at least 6 in from inside and outside corners, and if a partial width goes into a corner, make the joint on the flat wall with two factory edges, never a cut edge against a factory edge.

Outside corners: wrap, do not seam

An outside corner, such as the end of a chimney breast or a hallway return, takes knocks. A seam right on the edge will be picked at by bags and vacuum cleaners for years. Plan the layout so a strip wraps around the corner by at least an inch, and preferably several, before any seam occurs.

That planning happens on paper, not on the ladder. Before hanging, measure from your starting line to the outside corner and divide by the roll width. If a seam lands within an inch or two of the edge, move your starting plumb line a few inches. As with inside corners, draw a new plumb line on the far face; a wrapped edge almost never runs true.

Plan the wall before the first cut

Five minutes with a tape and a pencil saves most of the grief described above. Sketch the wall, mark every opening, and draw strip lines at roll-width spacing from your intended start. Look for problems: a seam that lands an inch from the window frame, a sliver above the door, a seam right on an outside corner. Shift the start until none of them occur.

Wolf-Gordon's guidance sums up the goal: avoid cutting narrow widths of material for placement above doors and below windows. On a 12 ft wall with 20.5 in strips, moving the start line 5 in usually moves every seam off a window edge. Keep the strip count the same, because each strip is still cut from a full drop.

  • Seams at least 1 in from window and door frames.
  • Seams at least 6 in from inside and outside corners where possible.
  • No piece narrower than about 4 in, anywhere.
  • Short strips over doors and under windows marked with their pattern start point.

Questions people ask

Do you subtract windows and doors when calculating wallpaper?

Usually not, or only partly. The pieces above and below an opening must still match the pattern, so they come from full drops or matching offcuts. RoomBatch counts full-height strips and keeps the cut-outs as spare, which is a safe default for most accent walls.

How do you wallpaper around an outlet?

Turn off power and remove the faceplate. Hang the paper over the box, cut an X from corner to corner, fold back the flaps and trim them to the box edge. Refit the faceplate once the paste is dry.

How do you wallpaper an inside corner?

Cut the strip so it wraps only about 1/2 in onto the next wall. Draw a new plumb line on that wall, then hang the remaining piece to the line so it overlaps the wrap. Never turn a full strip around an inside corner.

Can you wallpaper over a light switch plate?

You can cover a removed faceplate with a matching offcut, glued on the bench, so it disappears into the pattern. Never paper over a plate in place or inside the electrical box itself.

What if a seam lands right at the edge of a window?

Move your starting plumb line a few inches so seams sit at least an inch clear of the frame. Thin slivers beside frames lift and look messy, and shifting the start does not change how many strips you need.

Sources & further reading

  1. Brewster Home Fashions: How to hang wallpaper (PDF) (opens in a new tab)
  2. Wolf-Gordon: Grasscloth installation guidelines (PDF) (opens in a new tab)
  3. Brewster Home Fashions: How to hang prepasted wallpaper (opens in a new tab)

Planning information only. Product labels, manufacturer instructions and local codes take priority. Prices are illustrative. Read how we write and check guides in our editorial policy.

Was this guide useful?