roombatch

WallpaperHanging day

How to Hang the First Strip of Wallpaper Plumb (and Where to Start)

Every strip on the wall copies the first one, including its mistakes. Get the first strip vertical, start it in the right place and set the pattern at a deliberate height, and the rest of the wall mostly takes care of itself. This guide covers the layout decision most tutorials skip: where the first line goes so you never end with a half-inch sliver in the corner.

8 min readPublished By the RoomBatch editorial team
On this page
  1. Key takeaways
  2. Why plumb beats the corner every time
  3. Marking the line: the roll-width-minus-half-an-inch rule
  4. On an accent wall, plan the end widths first
  5. Set the pattern height before you cut
  6. Hanging the first strip, step by step
  7. Mistakes that ruin a first strip
  8. Lasers, plumb bobs and levels
  9. Questions

Key takeaways

  • Never trust a corner, door frame or ceiling to be straight. Draw a true vertical line with a level and hang to that.
  • Brewster's rule: measure out from the corner the roll width minus 1/2 in, mark, and draw your plumb line there.
  • On an accent wall, lay out the strips on paper first. Starting at a corner can leave a sliver at the far end; centering a seam or a strip can fix it.
  • Decide where the main motif sits at the ceiling before cutting the first drop. Every other strip inherits it.
  • Draw a new plumb line on every new wall and after every corner.

Why plumb beats the corner every time

Corners in real houses lean. A corner that drifts just 1/4 in over 8 ft looks perfectly straight to the eye, but if you butt your first strip into it, that lean is copied into every strip that follows. By the far end of a 12 ft wall, a pattern of level motifs can visibly tilt, and the last seam will not be parallel to the corner it meets.

A plumb line is a pencil line that is truly vertical, set with a spirit level, laser level or a plumb bob. You hang the leading edge of the first strip to the line and let the corner edge take whatever it gets, because that edge wraps or gets trimmed anyway. Brewster calls this the most crucial step in hanging wallpaper, and repeats it at every corner and every new wall.

Marking the line: the roll-width-minus-half-an-inch rule

Brewster's printed instructions give the method in three steps. Measure out from the corner the width of the paper minus 1/2 in and mark it with a pencil; for a 20.5 in roll that is 20 in. Place a level at the mark and draw a vertical line from ceiling to baseboard. Repeat the process each time you reach a corner or start a new wall.

That half inch is deliberate. With the strip's leading edge on the line, the trailing edge reaches 1/2 in past the corner, so a slightly out-of-plumb corner is still covered and you can trim it tidy. For a 0.53 m Euro roll, mark at about 52 cm, or 20.4 in.

Marking the line: the roll-width-minus-half-an-inch rule
Roll widthMark from cornerWhy
20.5 in (US)20 inLeaves 1/2 in to wrap or trim at the corner
0.53 m / 20.9 in (Euro)52 cm / about 20.4 inSame 1/2 in margin in metric
27 in (wide US)26.5 inWider rolls, same logic
36 in (grasscloth, some non-wovens)35.5 inCheck the maker; many specify double cutting seams

On an accent wall, plan the end widths first

Starting at a corner is fine when you wrap a whole room, because you hide the last seam in a dark corner. An accent wall is different: both ends are on show. Before you mark anything, divide the wall width by the roll width and look at the remainder.

Take a 12 ft (144 in) wall with 20.5 in US rolls. Seven full strips cover 143.5 in, so starting at the left corner leaves a 1/2 in sliver at the right end. That sliver is fiddly to hang, prone to lifting, and pulls attention to the corner. Wolf-Gordon's hanging guidance for natural wallcoverings goes further: plan equal widths with no short strips at an end, and keep vertical joints at least 6 in from inside and outside corners.

Now try centering. If a seam falls on the wall's center line, each half is 72 in: three full strips (61.5 in) plus a 10.5 in piece at each end. Balanced, and nothing near the corners is narrower than half a roll. If instead a strip is centered, each side has 61.75 in left, which is three strips plus a 1/4 in sliver at both ends. Worse. So on this wall you center a seam.

On an accent wall, plan the end widths first
Layout on a 144 in wallUS 20.5 in rollsEuro 20.9 in rolls
Start at left corner7 full + 0.5 in sliver6 full + 18.8 in end piece
Seam on the center line10.5 in at each end9.4 in at each end
Strip centered on the wall0.25 in sliver at each end19.8 in at each end
Best choiceCenter a seamStart at a corner or center a strip

Set the pattern height before you cut

Brewster suggests holding the uncut roll against the wall before pasting to see where the design falls, so the ceiling line does not slice through the middle of a key motif. On an accent wall, the eye lands on the top 2 ft first. A row of full flowers or a clean geometric line at the ceiling reads as intentional.

Once you choose that start point, you have fixed the pattern position for every straight-match strip and every second half-drop strip. That is why RoomBatch rounds each drop up to a whole repeat: wall height plus trim (4 in by default, the same 2 in top and 2 in bottom Brewster recommends) becomes a whole number of repeats. An 8 ft wall with a 21 in repeat needs 100 in, rounded to 105 in, so a 33 ft roll gives three drops.

If your ceiling is visibly out of level, favor a pattern with a stagger or a busy texture over a crisp horizontal stripe. Half-drops and all-over designs disguise a drifting ceiling line far better than motifs marching in a level row.

Hanging the first strip, step by step

With the line drawn and the drop cut to length (height plus 4 in), prepare the strip as its label says: soak and book prepasted, paste and book unpasted, or roll paste on the wall for paste-the-wall papers. Then work top down.

  • Turn off power to outlets and switches on the wall and remove faceplates before you start.
  • Unfold the top half and let about 2 in lap onto the ceiling.
  • Slide the strip so its leading edge sits exactly on the plumb line, not the corner.
  • Smooth from the center outward and downward with a brush or plastic smoother, without stretching the paper.
  • Unfold the bottom half and repeat, then recheck the edge against the line from top to bottom.
  • Trim ceiling and baseboard with a fresh blade against a wide putty knife; do not lift the knife mid-cut.
  • Sponge paste off the face, ceiling and trim with clean water before it dries.

Mistakes that ruin a first strip

Most problems on hanging day trace back to the first ten minutes. Here are the ones that cost the most, and the fix for each.

Mistakes that ruin a first strip
MistakeWhat happensFix
Hanging to the cornerEvery strip leans; last seam is not parallelHang to a level line set off the corner
No end-width checkA sliver strip at the far endDivide the wall by roll width; center a seam or strip
Upside-down stripPattern breaks at one seamPencil an arrow on the back of every strip
Stretching to close a gapSeam shrinks open as paste driesSlide the whole strip; never pull an edge
Dull bladeTorn, ragged ceiling lineSnap off a fresh blade segment every strip
One line for the whole roomError grows around cornersNew plumb line on every wall

Lasers, plumb bobs and levels

Any accurate vertical works. A 4 ft spirit level is the simplest: draw along it, slide it down, and continue the line to the baseboard. A plumb bob, a weight on a string, is cheap and true over the full height. A cross-line laser projects the line for you and is handy on tall walls, but check it is self-leveling and calibrated, and still pencil a short reference mark at the top and bottom in case it is bumped.

Whatever you use, check the line once more after the first strip is up. Paper that slipped while you smoothed it is far easier to fix in the first two minutes than after the second strip is matched to it.

Questions people ask

Where should I start hanging wallpaper on an accent wall?

Divide the wall width by the roll width first. If starting at a corner leaves a thin sliver at the other end, center a seam or a strip on the wall instead so both end pieces are generous. Then draw a plumb line at the first strip's leading edge.

How far from the corner do you draw the plumb line?

Brewster's instructions say to measure out the roll width minus 1/2 in. For a 20.5 in roll, mark 20 in from the corner and draw a level vertical line there.

Do I need a new plumb line for every strip?

No, only for the first strip on each wall and after each corner. Following strips butt to the previous one. Recheck with a level every few strips on long walls in case small errors build up.

How much extra length should I cut for the first strip?

Wall height plus about 4 in, 2 in at the ceiling and 2 in at the baseboard, then rounded up so the pattern starts where you want it. RoomBatch uses that 4 in trim by default and rounds to whole repeats.

Can I use a laser level for wallpaper?

Yes. A self-leveling cross-line laser is quick and accurate. Mark the line lightly in pencil at the top and bottom as a backup, because a bumped laser will silently move your reference.

Sources & further reading

  1. Brewster Home Fashions: How to hang wallpaper (PDF) (opens in a new tab)
  2. Brewster Home Fashions: How to hang prepasted wallpaper (opens in a new tab)
  3. Wolf-Gordon: Grasscloth installation guidelines (PDF) (opens in a new tab)

Planning information only. Product labels, manufacturer instructions and local codes take priority. Prices are illustrative. Read how we write and check guides in our editorial policy.

Was this guide useful?