roombatch

Methodology

Every number, shown.

All RoomBatch calculators and the wall studio share one calculation engine. This page sets out its formulas for all seven finishes, with worked examples computed live by that same engine.

Last updated October 5, 2026

Shared rules

A few rules apply to every finish:

  • One internal unit. Lengths are stored in feet and areas in square feet. Metric input is converted on the way in (1 m = 3.2808 ft) and back on the way out, so switching units never changes the answer.
  • Net area. For each wall, net area = width × height − the area of its openings. Openings are clipped to the wall and overlapping openings are counted once, never twice.
  • Allowance. Your allowance (default 10%) becomes a multiplier: allowance = 1 + waste ÷ 100. It covers offcuts, touch-ups and the odd mistake.
  • Round up once, at the end. Intermediate values stay unrounded; only the final quantity is rounded up to a whole container, roll, sheet, board or length.
  • Cutting lists use first-fit decreasing. For boards, slats and moulding, every piece is sorted longest first and placed in the first stock length with room for it; a new length is started only when none fits. Offcuts are reused when a piece fits in them.
  • Cost = quantity × the unit price you enter, plus any extras you add. Default prices are illustrative.

Paint

containers = ⌈ net area × coats × allowance ÷ coverage per container ⌉
primer (optional, one coat) = ⌈ net area × allowance ÷ primer coverage ⌉

Worked example. A 12′ × 8′ wall with one 3′ × 4′ window: gross area 96 ft², net 84 ft². Two coats at 350 ft² per can with a 10% allowance: 84 × 2 × 1.1 ÷ 350 = 0.53, which rounds up to 1. Primer: 84 × 1.1 ÷ 300 = 0.31, so 1 can.

Engine result

1 can · illustrative cost $86 · Net surface: 84 ft² · Coverage needed: 184.8 ft² · Before rounding: 0.53 cans

“Container” means whatever size you entered the coverage for. If your label says a gallon covers 250–400 ft², enter the lower figure for porous, patched or dark-to-light jobs. The calculator doesn’t guess pack sizes; you tell it.

Try it: Paint calculator

Limewash

containers = ⌈ net area × coats × allowance ÷ coverage per container ⌉

The same formula as paint with limewash’s own coverage and coat count (default 250 ft² per container, 2 coats). Worked example: a 14′ × 9′ wall has 126 ft². 126 × 2 × 1.1 ÷ 250 = 1.11, rounded up to 2.

Engine result

2 containers · illustrative cost $136 · Net surface: 126 ft² · Coverage needed: 277.2 ft² · Before rounding: 1.11 containers

Limewash coverage swings more than paint with surface porosity, so the engine always recommends brushing a sample board first.

Try it: Limewash calculator

Wallpaper

strips per wall = ⌈ wall width ÷ roll width ⌉
drop = wall height + trim
  straight or half-drop match: drop = ⌈ drop ÷ repeat ⌉ × repeat
  half-drop: every second strip adds ½ repeat
spare strips = ⌈ strips × allowance ⌉ − strips   (each as long as the longest drop)
rolls = drops packed into roll lengths (first-fit decreasing)

Wallpaper is counted in whole strips, not area. Openings are not deducted: a strip that runs over a window is still cut from a full drop, and the pieces you cut out become your spares.

Worked example. A 12′ × 8′ wall, rolls 20.5 in wide and 33′ long, 21 in straight-match repeat, 4 in total trim. Strips: 144 in ÷ 20.5 in → 8. Drop: 100 in rounds up to whole repeats → 5 × 21 in = 105 in. Spares: ⌈8 × 1.1⌉ − 8 = 1. That’s 9 drops of 105 in; one roll yields 3, so 3 rolls.

Engine result

3 rolls · illustrative cost $237 · Strips to hang: 8 · Spare strips: 1 · Longest drop: 8′ 9″ · Roll offcut: 20′ 3″

If a single drop is longer than a roll, the engine stops and says so instead of returning a misleading count.

Try it: Wallpaper calculator

Wall panels

columns = ⌈ wall width ÷ panel width ⌉
rows = ⌈ wall height ÷ panel height ⌉
panels = ⌈ Σ(columns × rows) × allowance ⌉

Worked example. A 13′ × 9′ wall with 2′ × 8′ sheets: 7 columns × 2 rows = 14 sheets; × 1.1 = 15.4, so 16 panels. The 9′ height needs a second row, which means a horizontal joint; the engine flags it.

Engine result

16 panels · illustrative cost $1,424 · Columns: 7 · Rows: 2 · Sheets before allowance: 14

It’s a full-sheet grid: openings aren’t deducted and offcuts aren’t assumed reusable, because patterned and fluted faces rarely allow it.

Try it: Wall panel calculator

Slat wall

slats = ⌈ (wall width + target gap) ÷ (slat width + target gap) ⌉
even gap = (wall width − slats × slat width) ÷ (slats − 1)
each slat runs full height, spliced from extra boards if taller than one board
boards = ⌈ boards from cutting list × allowance ⌉

Worked example. A 12′ wall, 1.75 in slats, 1.25 in target gap, 8′ boards: (144 in + 1.25 in) ÷ (1.75 in + 1.25 in) → 49 slats. Even gap: (144 in − 49 × 1.75 in) ÷ 48 = 1.21 in, so both ends finish on a slat. Each 8′ slat uses one 8′ board: 49 × 1.1 → 54 boards.

Engine result

54 boards · illustrative cost $756 · Slats across: 49 · Even gap (first wall): 1.21 in · Linear length: 392′

Try it: Slat wall calculator

Board & batten

gaps = max(1, round((wall width − board width) ÷ target spacing))
verticals = gaps + 1                     (one at each end)
actual spacing (centre to centre) = (wall width − board width) ÷ gaps
vertical length = batten height − 2 × board width   (when top and bottom rails are on)
rails = 2 × wall width, spliced at board length
boards = ⌈ boards from cutting list × allowance ⌉

Worked example. A 12′ wall, 2.5 in boards, 16 in target spacing, 5′ high with rails, 8′ boards: (144 in − 2.5 in) ÷ 16 in = 8.84, rounded to 9 gaps, so 10 verticals at 15.72 in centres. Each vertical is 55 in between the rails, and the two 12′ rails each splice from two boards.

Engine result

15 boards · illustrative cost $135 · Verticals: 10 · Even spacing (centres, first wall): 15.72 in · Batten height: 5′ · Linear length: 69′ 10″

Rounding to the nearest whole gap, rather than always up, keeps the actual spacing as close as possible to the one you asked for.

Try it: Board & batten layout

Picture-frame moulding

box width = (wall width − 2 × margin − (boxes − 1) × gap) ÷ boxes
without chair rail: box height = (wall height − 2 × margin − (rows − 1) × gap) ÷ rows
with chair rail (rail at ⅓ of wall height):
  lower box height = wall height ÷ 3 − 2 × margin
  upper box height = (wall height − wall height ÷ 3 − 2 × margin − (upper rows − 1) × gap) ÷ upper rows
pieces = 4 sides per box (+ chair rail across the full width), packed into stock lengths
lengths = ⌈ lengths from cutting list × allowance ⌉     mitre cuts = boxes × 8

Worked example. A 12′ × 8′ wall, 3 boxes per row, 2 rows with a chair rail, 4 in margins and gaps, 8′ lengths: box width = (144 in − 8 in − 8 in) ÷ 3 = 42.67 in. Lower boxes are 32 in − 8 in = 24 in tall; upper boxes are 96 in − 32 in − 8 in = 56 in tall. That’s 6 boxes and 48 mitre cuts.

Engine result

16 lengths · illustrative cost $192 · Boxes: 6 · Box size (first wall): 42.67 in × 24 in · Mitre cuts: 48 · Linear length: 94′ 8″

With a chair rail, the first row sits below the rail and any further rows share the space above it. Openings aren’t modelled for moulding; adjust boxes around windows by hand.

Try it: Picture-frame moulding

What the engine doesn’t know

  • The real absorbency of your wall, the roughness of your roller or how generously you load a brush.
  • Pack sizes in your local store. Enter the coverage and price for the container you’ll actually buy.
  • Whether your wall is plumb and square. Measure at several heights and use the largest figure (our measuring guide explains how).
  • Caulk, filler, adhesive, nails and tape. Add them as extras so they appear in the total.

Found a case where the numbers look wrong? Tell us the tool and the inputs. The engine is covered by automated tests, and every confirmed bug gets a new one.

Default product sizes used above: Paint, Limewash, Wallpaper, Wall panels, Slat wall, Board & batten, Picture-frame moulding use RoomBatch’s starting values, which you can change in every tool. Planning estimates only; always check the product label.