On this page
Key takeaways
- Do a water-drop test first: if water beads, the surface needs a mineral primer before limewash.
- Quantity = net area x coats x (1 + allowance) / label coverage, then round up to whole containers.
- Work in roughly 3 x 3 ft patches with random X strokes, always brushing back into wet edges.
- Let each coat dry fully (it lightens dramatically) before judging color or adding the next.
- The first coat looks blotchy on purpose. Judge the wall after the second coat has dried for a day.
Before you open the bucket: test porosity
Limewash needs to soak in. Flick a few drops of water onto the wall in three places. If the water darkens the surface and disappears within a minute, the wall is porous: bare plaster, brick, concrete block, unpainted skim coat or an existing mineral finish. Limewash can go straight on, often after lightly dampening the wall.
If the water beads or runs, you are looking at a sealed surface, almost always latex or oil paint. Limewash applied directly here will sit on the surface, stay chalky and can rub or peel off. You need a mineral or grip primer first, applied and cured according to its label. Glossy or oil-based paint needs a scuff sand and possibly a bonding primer before that.
Also check soundness. Press tape firmly on the wall and rip it off. If paint comes with it, fix that before anything else. Limewash will not hold a failing coating together.
| Water test result | Likely surface | What to do |
|---|---|---|
| Soaks in fast, darkens | Bare plaster, brick, block, mineral paint | Dampen lightly, then limewash |
| Soaks in slowly, patchy | Old plaster with patches, mixed repairs | Spot-prime patches or prime all for evenness |
| Beads or runs off | Latex paint, primer, sealer | Clean, scuff, mineral primer, cure |
| Beads on shiny surface | Oil or high-gloss paint | Sand, bonding primer, then mineral primer per label |
Work out how much to buy
Limewash labels quote coverage per gallon (or per liter) per coat, and the range is wide because porosity changes everything. Use the label's figure and this method: net area x coats x (1 + allowance) / coverage, then round up to whole containers.
Net area is width x height minus openings. Allowance covers waste, absorption and a wetter brush; 10 to 15% is sensible for limewash, more on very thirsty brick. Do the primer separately with its own coverage figure.
Worked example: a 14 x 9 ft living-room wall with a window
The wall is 14 ft wide and 9 ft tall: 126 sq ft. It has a 4 x 5 ft window, 20 sq ft, so net area is 106 sq ft. It is painted with eggshell latex, so it needs a primer.
Primer: 106 x 1 coat x 1.10 / 350 sq ft per gallon (illustrative label figure) = 0.33 gallons. Buy one quart if sold, otherwise one gallon.
Limewash: you want soft depth, so plan two coats with a possible third. Using an illustrative label figure of 300 sq ft per gallon per coat on primed walls: 106 x 2 x 1.15 / 300 = 0.81 gallons. With three coats: 106 x 3 x 1.15 / 300 = 1.22 gallons. If the product comes in one-gallon tins, two coats means one tin and three coats means two. That decision is worth making before you shop, not halfway through coat two.
Budget the job in days: primer and its cure time (often overnight), coat one, coat two later that day or next, and a final look in daylight after a full day of drying.
Tools and setup
Use a wide, soft block brush, roughly 4 to 6 in, with natural or blended bristles. A roller gives an even, paint-like finish and defeats the point. Have a spray bottle of clean water, a bucket for stirring, drop cloths, painter's tape and a damp rag.
Limewash is alkaline. Wear gloves and eye protection, especially when mixing powder or working overhead. Protect stone, wood floors and metal fixtures from splashes, and wipe drips immediately; dried lime on stone is hard to remove.
- Block brush, 4 to 6 in, plus a 2 in brush for edges
- Spray bottle, stir stick, bucket, gloves, glasses
- Drop cloths and tape; remove switch plates
- Good raking light (a work lamp held to the side shows misses)
Applying coat one
Stir thoroughly and keep stirring every few minutes; pigment settles. Thin only as the label allows, since thinner means more translucent and more coats. If the surface is mineral and porous, mist a 3 x 3 ft area with water so the first coat does not flash-dry.
Cut in corners and edges with the small brush, then immediately fill in with the block brush using loose, overlapping X or crisscross strokes. Work in roughly 3 x 3 ft patches, moving across and down, and always brush back into the wet edge of the previous patch. A wet edge is simply the still-wet border of the area you just did; if it dries before you join it, you get a hard line.
Do not overwork. Two or three passes over an area are enough. Do not stop in the middle of the wall for a break; finish to a corner or natural edge, because a dried line mid-wall shows forever.
Coat two, and knowing when to stop
Wet limewash looks dark and dramatic. As it dries it lightens a lot, often by several shades, and the final color only shows once it is fully dry. Wait the label's recoat time (often a few hours) and at least until the whole wall is even in color before starting coat two.
Coat two goes on the same way, but vary your stroke direction so the brush pattern does not stack into a grid. This coat evens out the patchiness of coat one while keeping movement. After it dries, look at the wall in daylight from the doorway. If it still looks too thin or too blotchy, add a third coat. If it looks too uniform, you over-brushed; the next wall will be better.
Leave the room to cure. Lime keeps hardening for weeks as it carbonates. Avoid hanging art or pushing furniture against it for a few days, and do not wash it.
Common mistakes
Most problems are easy to avoid once you know them.
- Skipping the water-drop test and limewashing straight over latex.
- Rolling instead of brushing, then wondering why it looks like flat paint.
- Judging color while wet and repainting a wall that was fine.
- Stopping mid-wall, leaving a dried edge that never blends.
- Not stirring often, so the bottom of the bucket is a different color.
- Buying for two coats when the look you want needs three.
Questions people ask
How many coats of limewash do you need?
Usually two. One coat gives a light, washed, antique look; two give a fuller color with movement; a third deepens and evens it. Plan your purchase for the coat count you want, and check the label, since products differ.
Can you roll limewash?
You can, but you lose the movement that makes limewash worth choosing. Some people roll on and immediately brush out with a block brush. For an accent wall, brushing alone is simpler and gives a better result.
Why does my limewash look patchy?
After the first coat, patchy is normal; the second coat evens it. If it is patchy after two dry coats, the surface likely has uneven porosity (repairs or mixed materials). A primer under the whole wall, or a third coat, usually fixes it.
How long does limewash take to dry?
It is often touch-dry within an hour or two and recoatable within a few hours, but it continues curing for weeks as it reacts with carbon dioxide. Follow your product's label for recoat times; humidity and temperature change them.
Do you need to seal limewash indoors?
Not usually on a low-touch accent wall. A breathable matte sealer can reduce chalking on walls that get touched, but it will change the look slightly. Test it on a sample board first.
Does limewash rub off on clothes?
A little loose chalk can come off in the first weeks or if the coat was applied too thin over a non-porous surface. Properly applied limewash on a suitable surface hardens and dusting reduces as it cures.
Terms in this guide
See it worked out
Sources & further reading
Planning information only. Product labels, manufacturer instructions and local codes take priority. Prices are illustrative. Read how we write and check guides in our editorial policy.