On this page
Key takeaways
- Mitre outside corners and picture frame boxes; cope inside corners on profiled moulding; butt flat stock.
- Measure the actual corner angle. Saw setting = (180 − corner angle) ÷ 2, so a 94 degree corner needs 43 degrees, not 45.
- A 1 degree error on 2 in moulding opens a gap of roughly 1/32 in per piece, so 1/16 in at the joint.
- Cut matching box sides together against a stop block so opposite sides are identical.
- Glue every mitre and pin across it; glued mitres stay closed far better than nailed-only ones.
Three joints, three jobs
Finish carpentry uses three corner joints over and over. A mitre cuts both pieces at an angle so they meet at the corner like a picture frame. A cope shapes the end of one piece to the profile of the other so it fits over it like a puzzle piece. A butt joint simply runs one square-cut piece into another.
Each has a job. Mitres are the only option for outside corners, where both faces are visible, and for every corner of a picture frame box on a flat wall. Copes are the professional choice for inside corners on profiled moulding such as baseboard, chair rail and crown, because they hide movement. Butt joints suit flat stock, which is why board and batten verticals simply butt into the rails.
| Joint | Use it for | Strength | Watch out for |
|---|---|---|---|
| Mitre | Outside corners, picture frame boxes | Clean look, shows every error | Opens if wood shrinks or the angle is off |
| Cope | Inside corners on profiled moulding | Forgiving, hides movement | Needs a coping saw and practice |
| Butt | Flat battens, rails, square stock | Fast and simple | Only works on flat profiles |
| Scarf | Joining two lengths on a long run | Hides a splice | Land it over a stud if you can |
Why inside corners are coped
Wood moves much more across its width than along its length. An inside mitre is two angled cuts pressed together; when the pieces shrink slightly in width, the joint opens into a visible dark line. A cope avoids that. The first piece runs square into the corner, and the second piece is cut to the shape of the first, so as the wood moves the coped piece simply slides over its neighbour.
Coped joints also tolerate walls that are not quite square, because the coped piece follows the profile rather than relying on a precise angle. That is why carpenters cope baseboard and chair rail almost by reflex.
MDF and PVC move less with humidity than solid wood, so inside mitres on those materials stay closed better. Copes are still easier to fit on an imperfect corner.
How to cut a cope, step by step
Install the first piece square-cut and tight into the corner. On the second piece, cut a 45 degree inside mitre, the cut you would make for a mitred inside corner. That exposes the moulding profile as a clean line along the front edge.
Darken that line with a pencil. Then follow it with a coping saw, holding the blade tilted back so you remove more from the back than the front (a back-cut). Finish with a file or a rotary tool, test against an offcut of the first piece, and adjust until the front edge meets the profile with no daylight.
- Keep a short offcut of the profile as a test block
- Back-cut by 5 to 15 degrees so only the front edge touches
- On flat-topped profiles, cut the flat part square with a fine saw first, then cope the curves
- Cut the coped piece 1/16 in long and spring it into place on a straight run
Mitres for out-of-square corners
Walls are rarely exactly 90 degrees, especially at outside corners with bulky corner bead. Measure the corner with an angle finder or a sliding bevel, then split it. The saw setting for each piece is (180 − corner angle) ÷ 2. A true 90 degree corner gives 45. A 94 degree outside corner gives 43. An 86 degree corner gives 47.
Why bother? Because small errors add up. On moulding 2 in wide, every degree of error opens a gap of about 2 × tan(1°) ≈ 0.035 in, roughly 1/32 in, at the heel of each piece. Both pieces off by a degree and you have a 1/16 in gap at the joint: enough to see, too wide to caulk invisibly.
| Measured corner | Saw setting each piece | Gap if you cut 45° (2 in moulding) |
|---|---|---|
| 86° | 47° | about 1/8 in |
| 88° | 46° | about 1/16 in |
| 90° | 45° | none |
| 92° | 44° | about 1/16 in |
| 94° | 43° | about 1/8 in |
Picture frame boxes: eight cuts each
On a flat wall, box corners are true 90 degree corners, so every cut is 45 degrees. A box has four sides and two mitres per side, so eight cuts per box. The six-box layout from our picture frame guide (three boxes 42.67 in wide in two rows, 24 in and 56 in tall) means 48 mitre cuts. A sharp fine-tooth blade is worth fitting before you start.
Measure box sides on the long point, the outside edge of the mitre. Set a stop block on the saw and cut both tops, both bottoms and both sides of each box size against it, so opposite sides are identical. Parallel sides of equal length guarantee a square box even if your 45 is slightly off; unequal sides guarantee a twisted one.
- Cut every piece of one length before moving the stop block
- Label pieces on the back with box number and side
- Dry-fit one box on the floor before gluing anything
Butt and scarf joints on battens and rails
Board and batten is mostly butt joints, which is good news. Verticals run square-cut between the bottom and top rails, and the end verticals butt into the adjoining wall. Cut each vertical to its measured length rather than one length for all, because floors and rails are rarely perfectly parallel. A vertical that is 1/16 in long will bow; one that is 1/16 in short leaves a gap that filler handles easily.
Long rails are the exception. On a 12 ft wall with 8 ft stock, each rail needs a splice. Cut both ends at a matching 45 degree bevel through the thickness so the pieces overlap, glue the joint, and land it over a stud if you can so you can nail through both pieces. A scarf joint sands and paints out almost invisibly, where a square butt splice tends to reappear as a hairline crack after a season.
Making mitres stay closed
A mitre held only by nails into the wall will open eventually. Put a dab of wood glue (or PVC cement on PVC) on both faces, push the joint closed, and drive a 23 gauge pin through the corner from each direction so the joint is locked to itself, not just to the wall. Use construction adhesive on the back of each piece and 18 gauge brads into studs where they cross.
Fill tiny gaps with wood filler, sand flush once dry, and prime. Caulk only where moulding meets the wall, never in a mitre; caulk stays soft and shows as a dull line after painting. Wear eye protection whenever the saw or nailer is running.
Questions people ask
Should I cope or mitre inside corners?
Cope profiled moulding such as baseboard, chair rail and crown on inside corners. The joint hides shrinkage and tolerates out-of-square walls. Flat stock can simply butt, and MDF inside mitres can work if the corner is square.
What angle do I cut for an out-of-square corner?
Measure the corner angle and set each cut to (180 − corner angle) ÷ 2. A 92 degree corner needs 44 degree cuts; an 88 degree corner needs 46 degree cuts.
Why do my mitre joints have gaps?
Usually the corner is not 90 degrees, the pieces are different lengths, or the wood has shrunk. Measure the angle, cut opposite sides against a stop block, and glue and pin every mitre so it cannot open later.
How do you measure picture frame moulding for mitre cuts?
Measure to the long point, the outer edge of each mitre, and cut both matching sides of each box against the same stop block. That keeps opposite sides identical and the box square.
Can I caulk gaps in mitre joints?
Avoid it. Caulk stays flexible and dull and shows through paint. Fill mitre gaps with wood filler, sand flush and prime. Save caulk for the joint between moulding and wall.
Terms in this guide
See it worked out
Sources & further reading
Planning information only. Product labels, manufacturer instructions and local codes take priority. Prices are illustrative. Read how we write and check guides in our editorial policy.