On this page
Key takeaways
- Slats = ceil((wall width + gap) ÷ (slat width + gap)); the real gap = (width − slats × slat width) ÷ (slats − 1).
- An 8 ft wall with 1x2 slats (1½ in actual) and a 1 in target gap needs 39 slats at a 0.99 in gap.
- On a 9 ft ceiling, 10 ft boards avoid 39 splices; with 8 ft stock the count jumps from 43 to 49 boards.
- Choose straight boards one by one, and stain or paint them before they go on the wall.
- Use a spacer cut to the real gap, but check against tape marks every few slats to stop drift.
Pick the slat and gap
Lumber is sold by nominal size, so measure what you actually buy. A 1x2 is about ¾ by 1½ in, a 1x3 about ¾ by 2½ in, a 1x4 about ¾ by 3½ in. The slat width and gap together set the character of the wall: narrow slats with tight gaps look refined and textural; wide slats with wide gaps look bolder and more graphic.
RoomBatch's slat wall calculator takes your slat width and a target gap, finds the number of slats that fits, and evens out the gap so both ends finish on a slat. Here is how that plays out on an 8 ft (96 in) wide wall.
| Slat (actual) | Target gap | Slats | Real gap | 8 ft boards (8 ft wall, +10%) |
|---|---|---|---|---|
| 1½ in (1x2) | ¾ in | 43 | 0.75 in | 48 |
| 1½ in (1x2) | 1 in | 39 | 0.99 in | 43 |
| 1½ in (1x2) | 1½ in | 33 | 1.45 in | 37 |
| 2½ in (1x3) | 1 in | 28 | 0.96 in | 31 |
| 2½ in (1x3) | 1½ in | 25 | 1.40 in | 28 |
| 3½ in (1x4) | 1½ in | 20 | 1.37 in | 22 |
Worked example and cut list
Take a wall 96 in wide and 96 in tall, 1x2 slats and a 1 in target. (96 + 1) ÷ (1.5 + 1) = 38.8, so 39 slats. The real gap is (96 − 39 × 1.5) ÷ 38 = 37.5 ÷ 38 = 0.987 in, a hair under 1 in. Each slat is one 8 ft board, so 39 boards, 43 with a 10% allowance for warped or split pieces. That is 312 linear ft of slat.
Walls are rarely exactly 96 in tall, so measure the height at several points. If it is 96⅜ in at one end, an 8 ft board will leave a gap at the ceiling or floor. Plan to stop slats a deliberate ½ in short at the floor (hidden by a shadow or a baseboard) or to finish with a top trim.
Now raise the ceiling to 9 ft (108 in). With 8 ft stock, each slat needs a 96 in piece and a 12 in piece. RoomBatch packs the 12 in pieces eight to a board, so 44 boards, 49 with the allowance, and 39 visible splices. With 10 ft boards, each slat comes from one board with 12 in to spare: 39 boards, 43 with allowance, and no splices.
Choosing the lumber
Straightness is everything. A slat with a slight crook (curve along its edge) makes a gap that tapers, and the eye spots it instantly against its neighbours. Sight down every board at the store and reject any with crook, twist or a big knot near an edge. Bow along the face is less of a problem because fixing pulls it flat.
Common choices are select pine (clear, cheap, takes paint well, blotchy with stain unless pre-conditioned), poplar (smooth, paint-grade, often greenish), and oak (beautiful stained, harder to nail, more expensive). Primed MDF strips are straight and cheap for a painted wall but chip at the edges. As an illustration only, 43 eight-foot 1x2 boards might cost anywhere from about $170 to $390 depending on species and region.
- Buy all boards from one batch and one store
- Let wood sit in the room for a few days before cutting
- Buy 10% extra; some boards will move once cut
Finish before you fix
Stain or paint the slats before they go up. Finishing between narrow gaps on the wall is slow and messy, and the gaps never look clean. Lay the boards across sawhorses, finish all four long faces, and let them dry fully.
Then decide the background. The wall behind the slats shows through every gap, so paint it a dark color (black or a deep brown) for a classic shadowed look, or the same color as the slats for a monochrome finish. Some people mount the slats on black acoustic felt or a black-painted MDF backer, which also gives the slats something to fix into between studs.
Fixing slats straight and evenly
Locate the studs and mark them lightly on the floor and ceiling. Scan for cables and pipes before nailing; they often run straight up and down from outlets and switches. Fix each slat with a thin bead of construction adhesive and 18 gauge brad nails (about 1¼ to 1½ in for ¾ in slats into drywall over studs, longer if you are going through a backer). Ventilate while the adhesive cures.
Set the first slat dead plumb with a level; every other slat follows it. Cut a spacer block to the real gap (0.99 in in our example: rip a scrap to just under 1 in and check it with calipers or against a ruler), and use two spacers, top and bottom, for each slat.
Spacers drift because slats vary slightly in width. Mark the edge of every fifth slat on the wall from a single tape measurement (slat n starts at n × 2.487 in in our example) and check against it as you go. Correct a little each slat rather than all at once.
- Slat 5 should start at 12.43 in, slat 10 at 24.87 in, slat 20 at 49.74 in
- Check plumb every few slats as well as spacing
- Hide nails in a consistent pattern, or use a 23 gauge pinner on visible faces
Outlets, ends and edges
Slats sit ¾ in proud of the wall, plus any backer. An outlet that falls in the slat area needs a box extender to bring the device flush with the slat face, or you can leave it on the wall and stop the slats neatly around the plate. Turn off the breaker before removing a cover plate, and call an electrician if a box must move. Try shifting the slat count by one; it moves every middle slat and may clear the outlet altogether.
Decide how the slats end at the ceiling and floor. A clean ½ in shadow gap at the top looks modern; a slim trim piece hides an uneven ceiling. At the sides, the outermost slats sit tight into the corners because the calculator evens the gap to finish on a slat at both ends.
Questions people ask
How many slats do I need for a slat wall?
Slats = ceil((wall width + gap) ÷ (slat width + gap)). An 8 ft wall with 1½ in slats and a 1 in target gap needs 39 slats; add about 10% extra boards for warped or split pieces.
What size gap should a slat wall have?
Most DIY slat walls use gaps between ½ and 1½ in, usually a little narrower than the slats. Treat your gap as a target and let the calculator even it out so both ends finish on a slat.
What wood is best for a DIY slat wall?
Select pine and poplar for painted walls, oak or another hardwood for stained ones. Whatever you choose, the boards must be straight; reject any with a crook along the edge.
Should I paint the wall behind wood slats?
Yes, before installing. A dark color behind the slats deepens the shadows and makes the gaps look crisp. Painting the slats and wall the same color gives a quieter, monochrome look.
How do you attach wood slats to a wall?
Construction adhesive plus 18 gauge brad nails, nailing into studs where possible. Fixing to a backer board or felt panel gives you something to nail into between studs.
Terms in this guide
See it worked out
Sources & further reading
Planning information only. Product labels, manufacturer instructions and local codes take priority. Prices are illustrative. Read how we write and check guides in our editorial policy.