On this page
Key takeaways
- Plan with the exposure (visible face), not the board width; rabbeted shiplap overlaps, so a 1x6 might show about 5⅛ in.
- Rows = wall height ÷ exposure. Split the leftover between top and bottom rows so neither is a sliver.
- A 12 ft by 8 ft wall in 5⅛ in exposure needs 19 rows; with 8 ft boards that is 29 boards, 32 with 10%.
- Land butt joints on studs and stagger them so no two neighbouring rows share a joint line.
- Paint or prime the board edges before install so seasonal gaps never show bare wood.
Real shiplap, faux shiplap and the number that matters
True shiplap has a rabbet along each edge, so neighbouring boards overlap and leave a small shadow line. Because of that overlap, each board covers less wall than its width. A nominal 1x6 shiplap board (about 5½ in wide) might expose roughly 5⅛ in, depending on the profile. That visible face, the exposure, is the number you plan with.
Faux shiplap is usually plywood or MDF ripped into strips (often 6 or 8 in) and nailed up with a small gap, commonly set with a coin or a spacer. No rabbet means the strip width is the exposure, plus the gap. A 4 by 8 ft sheet of ¼ in plywood rips into seven full 6 in strips with a ⅛ in saw kerf, with a narrow strip left over.
Tongue-and-groove and nickel-gap boards sit in between: profiled edges like shiplap, with a built-in reveal. Check the maker's listed coverage width.
| Product | Plan with | Typical look |
|---|---|---|
| Rabbeted shiplap (1x6) | Exposure, about 5⅛ in | Classic, shadow line |
| Nickel-gap board | Listed coverage width | Crisp, even reveal |
| Ripped plywood strips | Strip width + gap | Budget, painted |
| MDF shiplap panels | Listed coverage width | Smooth, paint-grade |
Counting rows and balancing the ends
Divide the wall height by the exposure. On a 96 in tall wall with 5⅛ in exposure: 96 ÷ 5.125 = 18.73, so 18 full rows and a partial, 19 rows in all. If you start with a full board at the floor and work up, the top row is a 3¾ in strip, ripped down and squeezed under the ceiling. It looks like what it is.
Balance it instead. Use 17 full rows in the middle (87⅛ in), and split the remaining 8⅞ in between the top and bottom rows, about 4⁷⁄₁₆ in each. Both ends then look intentional. The same logic applies to vertical shiplap across the width of a wall.
RoomBatch's slat wall calculator handles this kind of even layout. For vertical shiplap, enter the exposure as the slat width and the reveal (or a tiny value for tight shiplap) as the gap. For horizontal shiplap, enter the wall height as the width. It will tell you how many boards fit and pack them into your stock lengths.
Worked example: 12 ft by 8 ft wall
Horizontal 1x6 shiplap with 5⅛ in exposure on a 144 in wide, 96 in tall wall: 19 rows, each 144 in long. With 8 ft boards, each row takes one full board and a 4 ft piece. Two 4 ft pieces come from one board, so 19 full boards plus 10 boards for the short pieces: 29 boards, 32 with a 10% allowance. With 12 ft boards, each row is one board, 19 in all, 21 with allowance, and no butt joints at all.
Faux shiplap from 6 in plywood strips on the same wall: 16 rows (the last one ripped narrower). Each row needs 1½ eight-foot strips, so 24 strips, and at seven strips per sheet that is 4 sheets of plywood with a few strips spare.
| Build (12 × 8 ft wall) | Rows | Stock | To buy (with allowance) |
|---|---|---|---|
| 1x6 shiplap, 8 ft boards | 19 | 29 boards | 32 boards |
| 1x6 shiplap, 12 ft boards | 19 | 19 boards | 21 boards |
| 6 in plywood strips | 16 | 24 strips | 4–5 sheets |
Joints, studs and stagger
Real shiplap is heavy enough that it should be nailed into studs, which in most US homes sit 16 in apart on centre. Find them, mark each one with a vertical pencil or laser line, and plan butt joints to land on a stud so both board ends get a nail.
Stagger the joints so neighbouring rows never share a joint line. A simple pattern on a 12 ft wall is to alternate the 4 ft piece left and right: one row has its joint at 8 ft from the left, the next at 4 ft. Both positions are multiples of 16 in, so if your first stud is 16 in from the corner, both land on studs. Real walls rarely start that neatly, so check and adjust.
Before nailing, scan for cables and pipes. They often run vertically above and below outlets and switches, and horizontally near countertops in kitchens.
- Nail through the face into studs with 2 in brads or finish nails, two per stud per board
- On faux shiplap, add a thin bead of construction adhesive and ventilate while it cures
- Start the first row on a level line, not on the floor or baseboard
Outlets, corners and edges
Shiplap covers the wall, so every outlet and switch inside it needs a cut-out and, because the surface moves out by the board thickness, usually a box extender to bring the device flush. Turn off the breaker first, and call an electrician if a box needs moving. Cut openings slightly oversize; the cover plate hides up to about ⅛ in around the box.
Inside corners can butt. Outside corners can be mitred at 45 degrees or finished with a vertical corner board, which is more robust in a hallway. Leave a small gap at the ceiling and floor for movement and cover it with trim or caulk.
Window and door casings either stay on top of the shiplap (remove and refit them after) or the shiplap butts into them. If the casing is shallow, the boards may stand proud of it, so check before you start.
Finishing
Wood moves with the seasons, so gaps open and close slightly. Prime and paint the edges and rabbets before installation; otherwise a winter gap reveals a stripe of raw wood. Then fill nail holes, sand, caulk where boards meet trim, and give the face its final coats on the wall.
Do not caulk the shadow lines between boards. They are the whole point, and caulked shiplap just looks like a bumpy wall. Satin or eggshell suits most rooms; semi-gloss in kitchens and baths.
Questions people ask
How do I calculate how much shiplap I need?
Divide the wall height by the board's exposure (visible face) to get rows, then multiply rows by wall width for linear feet. Pack the rows into your board lengths and add about 10%. A 12 by 8 ft wall in 5⅛ in exposure needs about 32 eight-foot boards.
Should shiplap go horizontal or vertical?
Horizontal widens a room and is the classic look. Vertical makes ceilings feel taller. The planning is the same, turned 90 degrees.
Does shiplap need to be nailed into studs?
Real board shiplap should be nailed into studs. Light ¼ in plywood strips can be held by adhesive and angled brads between studs, but nail into studs wherever a strip crosses one.
Should I start shiplap at the top or bottom?
Plan the whole wall first, balancing the top and bottom rows. Then start at the bottom on a level line so every row above stays level, regardless of the floor.
What gap should I leave between faux shiplap boards?
A small, consistent reveal, commonly set with a coin or a thin spacer. Whatever you pick, use the same spacer for every row and check against level lines as you go.
Terms in this guide
Sources & further reading
Planning information only. Product labels, manufacturer instructions and local codes take priority. Prices are illustrative. Read how we write and check guides in our editorial policy.