On this page
Key takeaways
- Size the arch to the furniture: 6–12 in wider than the headboard or desk on each side, top at least 12–18 in above it.
- Draw the curve with a string compass: a nail at the center, string equal to half the arch width, pencil at the end.
- Arch area = rectangle (width × straight height) + semicircle (π × r² ÷ 2).
- Hand-cut curves with a small angled brush, or use flexible fine-line tape; standard tape creases on curves.
- Most arches need one quart, but a dark color at three coats can use nearly all of it.
Sizing an arch so it looks intentional
A painted arch reads as architecture only when it relates clearly to something: a bed, a desk, a console, a mirror, a doorway. Measure that object first. The arch should be wider than it by a deliberate amount, typically 6–12 in on each side. If it is only slightly wider, it looks like a misjudged shadow; if it is enormous, it stops framing anything.
Height matters just as much. Behind a bed, run the arch from the floor (or the top of the baseboard) to at least 12–18 in above the headboard, and keep a clear band of at least 12 in below the ceiling so the curve has room to breathe. Over a desk, a tall narrow arch often looks better than a wide squat one, and it gives video calls a neat background.
- Queen headboard (about 60–64 in wide): arch roughly 72–84 in wide.
- Twin bed or desk (about 40–48 in): arch roughly 52–64 in wide.
- Entry bench or console: arch about 12 in wider than the furniture, top at or just above door-head height.
- Rooms with 8 ft ceilings: keep the apex at or below about 84 in so the arch does not crowd the ceiling.
Shapes and their areas
You need area for paint and proportions for layout. These formulas cover almost every painted shape you will see on an accent wall. Work in feet for square feet, or meters for square meters, and do not mix them.
| Shape | Area formula | Example | Area |
|---|---|---|---|
| Classic arch | w × h(straight) + π × (w/2)² ÷ 2 | 4 ft wide, 5 ft straight + 2 ft radius top | 26.3 sq ft |
| Circle | π × r² | 36 in (3 ft) diameter | 7.1 sq ft |
| Half circle (sunrise) | π × r² ÷ 2 | 8 ft wide, 4 ft radius | 25.1 sq ft |
| Rectangle block | w × h | 3 ft × 6 ft | 18 sq ft |
| Triangle | base × height ÷ 2 | 6 ft base, 4 ft tall | 12 sq ft |
Drawing a perfect curve with a string compass
Forget stencils and freehand. Mark a vertical center line for the arch with a level. Decide where the straight sides end and the curve begins: that height is the springing line. The center of the curve sits on the center line at the springing height. Tap a small nail or press a pushpin there.
Tie a string to the nail and a pencil at a distance equal to half the arch width (the radius). Keep the string taut and the pencil upright, and swing a smooth arc from one side to the other. Then drop plumb lines from each end of the arc to the floor with a level. Fill the nail hole later with a dab of spackle; it is inside the painted area anyway.
For a circle, the method is identical: nail at the center, string at the radius, swing a full circle. A non-stretch string (mason's line) is better than yarn, which stretches and makes the curve wobble.
Getting a clean curved edge
Standard painter's tape cannot follow a tight curve without creasing, and every crease lets paint under. You have two good options. The first is flexible fine-line or vinyl masking tape, which stretches around curves; lay it in short overlapping lengths, burnish, and seal the edge with the wall color underneath before painting the arch.
The second is hand-cutting with a 1.5 in angled brush or a good artist's brush. On a curve this is often faster and cleaner than taping. Brace your painting hand's little finger against the wall, rotate your body rather than your wrist as you follow the line, and keep the brush loaded lightly. Do two coats, each slightly more confident than the last.
The straight sides can use normal tape. Fill the field with a small 4 in roller, keeping a few inches from the curve so the brush work and the roller texture blend.
Worked example: a 4 ft arch behind a desk
A desk is 40 in wide. The arch will be 48 in (4 ft) wide and 7 ft tall overall: 5 ft of straight sides plus a semicircular top with a 2 ft radius. Area: rectangle 4 × 5 = 20 sq ft; semicircle π × 2² ÷ 2 = 6.28 sq ft; total 26.3 sq ft (about 2.4 m²).
RoomBatch's method: net area × coats × (1 + allowance) ÷ coverage per can, rounded up. With a 10% allowance and a mid-tone color at two coats: 26.3 × 2 × 1.10 = 57.9 sq ft. At 350 sq ft per gallon, a quart covers 87.5 sq ft, so 57.9 ÷ 87.5 = 0.66, one quart.
Switch to a deep terracotta at three coats: 26.3 × 3 × 1.10 = 86.8 sq ft; 86.8 ÷ 87.5 = 0.99. One quart, with almost nothing left for touch-ups. If the label's low coverage figure is 300 sq ft per gallon (75 per quart), 86.8 ÷ 75 = 1.16 means two quarts. With dark colors on small shapes, buy the second quart or keep the first quart's last inch strictly for touch-ups.
Variations worth trying
Once you can draw one arch, the variations are easy. Two overlapping arches in close tones look custom and soft. An arch that continues up onto the ceiling as a curved band makes a reading nook. A half-circle sunrise behind a low headboard is the simplest curve of all, since it needs no plumb lines.
A thin painted outline of an arch, rather than a solid fill, reads like a door frame. Tape two concentric curves an inch or two apart, or hand-cut both edges. It uses almost no paint but takes more patience than a solid shape.
Questions people ask
How do you paint a perfect arch on a wall?
Draw the curve with a string compass: a nail at the center point on the springing line and a pencil tied at a distance equal to half the arch width. Drop plumb lines for the sides, then hand-cut or use flexible tape for the curve.
How wide should a painted arch be behind a bed?
About 6–12 in wider than the headboard on each side. For a queen headboard around 60 in wide, a 72–84 in arch frames it without looking oversized.
What tape works on curves?
Flexible fine-line or vinyl masking tape stretches around curves without creasing. Standard painter's tape wrinkles and lets paint bleed, so use it only on the straight sides.
How much paint do I need for a painted arch?
Usually one quart. Calculate arch area as width × straight height plus π × radius² ÷ 2, multiply by coats and 1.10, then divide by about 87 sq ft per quart. Dark colors at three coats can need two quarts.
How tall should a painted arch be?
Behind furniture, take the apex at least 12–18 in above the headboard or desk, while leaving 12 in or more below the ceiling. In 8 ft rooms that usually puts the top at about 78–84 in.
See it worked out
Planning information only. Product labels, manufacturer instructions and local codes take priority. Prices are illustrative. Read how we write and check guides in our editorial policy.